Cable Modem Motorola

Coaxial cable

How it works

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Coaxial cable cutaway

Like any electrical power cord, coaxial cable conducts AC electric current between locations. Like these other cables, it has two conductors, the central wire and the tubular shield. At any moment the current is traveling outward from the source in one of the conductors, and returning in the other. However, since it is alternating current, the current reverses direction many times a second. Coaxial cable differs from other cable because it is designed to carry radio frequency current. This has a frequency much higher than the 50 or 60 Hz used in mains (electric power) cables, reversing direction millions to billions of times per second. Like other types of radio transmission line, this requires special construction to prevent power losses:

If an ordinary wire is used to carry high frequency currents, the wire acts as an antenna, and the high frequency currents radiate off the wire as radio waves, causing power losses. To prevent this, in coaxial cable one of the conductors is formed into a tube and encloses the other conductor. This confines the radio waves from the central conductor to the space inside the tube. To prevent the outer conductor, or shield, from radiating, it is connected to electrical ground, keeping it at a constant potential.

The dimensions and spacing of the conductors are uniform. Any abrupt change in the spacing of the two conductors along the cable tends to reflect radio frequency power back toward the source, causing a condition called standing waves. This acts as a bottleneck, reducing the amount of power reaching the destination end of the cable. To hold the shield at a uniform distance from the central conductor, the space between the two is filled with a semirigid plastic dielectric. Manufacturers specify a minimum bend radius to prevent kinks that would cause reflections. The connectors used with coax are designed to hold the correct spacing through the body of the connector.

Each type of coaxial cable has a characteristic impedance depending on its dimensions and materials used, which is the ratio of the voltage to the current in the cable. In order to prevent reflections at the destination end of the cable from causing standing waves, any equipment the cable is attached to must present an impedance equal to the characteristic impedance (called 'matching'). Thus the equipment "appears" electrically similar to a continuation of the cable, preventing reflections. Common values of characteristic impedance for coaxial cable are 50 and 75 ohms.

Description

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Coaxial cable design choices affect physical size, frequency performance, attenuation, power handling capabilities, flexibility, strength and cost. The inner conductor might be solid or stranded; stranded is more flexible. To get better high-frequency performance, the inner conductor may be silver plated. Sometimes copper-plated iron wire is used as an inner conductor.

The insulator surrounding the inner conductor may be solid plastic, a foam plastic, or may be air with spacers supporting the inner wire. The properties of dielectric control some electrical properties of the cable. A common choice is a solid polyethylene (PE) insulator, used in lower-loss cables. Solid Teflon (PTFE) is also used as an insulator. Some coaxial lines use air (or some other gas) and have spacers to keep the inner conductor from touching the shield.

Conventional coaxial cable has braided copper wire forming the shield. This allows the cable to be flexible, but it also means there are gaps in the shield layer, and the inner dimension of the shield varies slightly because the braid cannot be flat. Sometimes the braid is silver plated. For better shield performance, some cables have a double-layer shield. The shield might be just two braids, but it is more common now to have a thin foil shield covered by a wire braid. Some cables may invest in more than two shield layers, such as "quad-shield" which uses four alternating layers of foil and braid. Other shield designs sacrifice flexibility for better performance; some shields are a solid metal tube. Those cables cannot take sharp bends, as the shield will kink, causing losses in the cable.

Coaxial cables require an internal structure of an insulating (dielectric) material to maintain the spacing between the center conductor and shield. The dielectric losses increase in this order: Ideal dielectric (no loss), vacuum, air, Polytetrafluoroethylene (PTFE), polyethylene foam, and solid polyethylene. A low relative permittivity allows for higher frequency usage. An inhomogeneous dielectric needs to be compensated by a non-circular conductor to avoid current hot-spots.

Most cables have a solid dielectric; others have a foam dielectric which contains as much air as possible to reduce the losses. Foam coax will have about 15% less attenuation but can absorb moisturespecially at its many surfacesn humid environments, increasing the loss. Stars or spokes are even better but more expensive. Still more expensive were the air spaced coaxials used for some inter-city communications in the middle 20th Century. The center conductor was suspended by polyethylene discs every few centimeters. In a miniature coaxial cable such as an RG-62 type, the inner conductor is supported by a spiral strand of polyethylene, so that an air space exists between most of the conductor and the inside of the jacket. The lower dielectric constant of air allows for a greater inner diameter at the same impedance and a greater outer diameter at the same cutoff frequency, lowering ohmic losses. Inner conductors are sometimes silver plated to smooth the surface and reduce losses due to skin effect. A rough surface prolongs the path for the current and concentrates the current at peaks and thus increases ohmic losses.

The insulating jacket can be made from many materials. A common choice is PVC, but some applications may require fire-resistant materials. Outdoor applications may require the jacket to resist ultraviolet light and oxidation. For internal chassis connections the insulating jacket may be omitted.

The ends of coaxial cables are usually made with RF connectors.

Signal propagation

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Open wire transmission lines have the property that the electromagnetic wave propagating down the line extends into the space surrounding the parallel wires. These lines have low loss, but also have undesirable characteristics. They cannot be bent, twisted or otherwise shaped without changing their characteristic impedance, causing reflection of the signal back toward the source. They also cannot be run along or attached to anything conductive, as the extended fields will induce currents in the nearby conductors causing unwanted radiation and detuning of the line. Coaxial lines solve this problem by confining the electromagnetic wave to the area inside the cable, between the center conductor and the shield. The transmission of energy in the line occurs totally through the dielectric inside the cable between the conductors. Coaxial lines can therefore be bent and moderately twisted without negative effects, and they can be strapped to conductive supports without inducing unwanted currents in them. In radio-frequency applications up to a few gigahertz, the wave propagates primarily in the transverse electric magnetic (TEM) mode, which means that the electric and magnetic fields are both perpendicular to the direction of propagation. However, above a certain cutoff frequency, transverse electric (TE) and/or transverse magnetic (TM) modes can also propagate, as they do in a waveguide. It is usually undesirable to transmit signals above the cutoff frequency, since it may cause multiple modes with different phase velocities to propagate, interfering with each other. The outer diameter is roughly inversely proportional to the cutoff frequency. A propagating surface-wave mode that does not involve or require the outer shield but only a single central conductor also exists in coax but this mode is effectively suppressed in coax of conventional geometry and common impedance. Electric field lines for this TM mode have a longitudinal component and require line lengths of a half-wavelength or longer.

Connectors

A coaxial connector (male N-type).

Main article: RF connector

Coaxial connectors are designed to maintain a coaxial form across the connection and have the same well-defined impedance as the attached cable. Connectors are often plated with high-conductivity metals such as silver or gold. Due to the skin effect, the RF signal is only carried by the plating and does not penetrate to the connector body. Although silver oxidizes quickly, the silver oxide that is produced is still conductive. While this may pose a cosmetic issue, it does not degrade performance.

Important parameters

Coaxial cable is a particular kind of transmission line, so the circuit models developed for general transmission lines are appropriate. See Telegrapher's equation.

Schematic representation of the elementary components of a transmission line.

Schematic representation of a coaxial transmission line, showing the characteristic impedance Z0.

Physical parameters

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Outside diameter of inner conductor, d.

Inside diameter of shield, D.

Dielectric constant of the insulator, . The dielectric constant is often quoted as the relative dielectric constant r referred to the dielectric constant of free space 0: = r0. When the insulator is a mixture of different dielectric materials (e.g., polyethylene foam is a mixture of polyethylene and air), then the term effective dielectric constant eff is often used.

Magnetic permeability of the insulator. Permeability is often quoted as the relative permeability r referred to the permeability of free space 0: = r0. The relative permeability will almost always be 1.

Fundamental electrical parameters

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Shunt Capacitance per unit length, in farads per metre.

Series Inductance per unit length, in Henrys per metre.

Series Resistance per unit length, in ohms per metre. The resistance per unit length is just the resistance of inner conductor and the shield at low frequencies. At higher frequencies, skin effect increases the effective resistance by confining the conduction to a thin layer of each conductor.

Shunt Conductance per unit length, in siemens per metre. The shunt conductance is usually very small because insulators with good dielectric properties are used (a very low loss tangent). At high frequencies, a dielectric can have a significant resistive loss.

Derived electrical parameters

Characteristic impedance in ohms (). Neglecting resistance per unit length for most coaxial cables, the characteristic impedance is determined from the capacitance per unit length (C) and the inductance per unit length (L). The simplified expression is (). Those parameters are determined from the ratio of the inner (d) and outer (D) diameters and the dielectric constant (). The characteristic impedance is given by

Assuming the dielectric properties of the material inside the cable do not vary appreciably over the operating range of the cable, this impedance is frequency independent above about five times the shield cutoff frequency. For typical coaxial cables, the shield cutoff frequency is 600 (RG-6A) to 2,000 Hz (RG-58C).

Attenuation (loss) per unit length, in decibels per meter. This is dependent on the loss in the dielectric material filling the cable, and resistive losses in the center conductor and outer shield. These losses are frequency dependent, the losses becoming higher as the frequency increases. Skin effect losses in the conductors can be reduced by increasing the diameter of the cable. A cable with twice the diameter will have half the skin effect resistance. Ignoring dielectric and other losses, the larger cable would halve the dB/meter loss. In designing a system, engineers consider not only the loss in the cable, but also the loss in the connectors.

Velocity of propagation, in meters per second. The velocity of propagation depends on the dielectric constant and permeability (which is usually 1).

Cutoff frequency is determined by the possibility of exciting other propagation modes in the coaxial cable. The average circumference of the insulator is (D + d) / 2. Make that length equal to 1 wavelength in the dielectric. The TE01 cutoff frequency is therefore

.

Peak Voltage

Outside diameter, which dictates which connectors must be used to terminate the cable.

Significance of impedance

The best coaxial cable impedances in high-power, high-voltage, and low-attenuation applications were experimentally determined in 1929 at Bell Laboratories to be 30, 60, and 77 respectively. For an air dielectric coaxial cable with a diameter of 10 mm the attenuation is lowest at 77 ohms when calculated for 10 GHz. The curve showing the power handling maxima at 30 ohms can be found here:

CATV systems were one of the first applications for very large quantities of coaxial cable. CATV is typically using such low levels of RF power that power handling and high voltage breakdown characteristics were totally unimportant when compared to attenuation. Moreover, many CATV headends used 300 ohm folded dipole antennas to receive off the air TV signals. 75 ohm coax made a nice 4:1 balun transformer for these antennas as well as presented a nice attenuation specification. But this is a bit of a red herring, when normal dielectrics are added to the equation the best loss impedance drops down to values between 64 and 52 ohms. Details and a graph showing this effect can be found here: [citation needed] 30 cable is more difficult to manufacture due to the much larger center conductor and the stiffness and weight it adds.

The arithmetic mean between 30 ohms and 77 ohms is 53.5, the geometric mean is 48 ohms. The selection of 50 ohms as a compromise between power handling capability and attenuation is generally cited as the reason for the number.

One reference to a paper presented by Bird Electronic Corp as to why 50 ohms was chosen can be found here:

50 Ohms works out well for other reasons such as it corresponds very closely to the drive impedance of a half wave dipole antenna in real environments, and provides an acceptable match to the drive impedance of quarter wave monopoles as well. 73 is an exact match for a centre fed dipole aerial/antenna in free space (approximated by very high dipoles without ground reflections).

RG-62 is a 93 ohm coaxial cable. It is purported that RG-62 cable was originally used in mainframe computer networks. (1970's / early 1980s). It was the cable used to connect the terminals to the terminal cluster controllers. Later some manufacturers of LAN equipment such as ARCNET adopted RG-62 as a standard. It has the lowest capacitance per unit length when compared to other coaxial cables of similar size. Capacitance is the enemy of square wave data transmission and is much more important than power handling or attenuation specifications in these environments.

All of the components of a coaxial system should have the same impedance to reduce internal reflections at connections between components. Such reflections increase signal loss and can result in the reflected signal reaching a receiver with a slight delay from the original. In analog video or TV systems this visual effect is commonly referred to as ghosting. (see Impedance matching)

Issues

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Signal leakage

Signal leakage is the passage of electromagnetic fields through the shield of a cable and occurs in both directions. Ingress is the passage of an outside signal into the cable and can result in noise and disruption of the desired signal. Egress is the passage of signal intended to remain within the cable into the outside world and can result in a weaker signal at the end of the cable and radio frequency interference to nearby devices.

For example, in the United States, signal leakage from cable television systems is regulated by the FCC, since cable signals use the same frequencies as aeronautical and radionavigation bands. CATV operators may also choose to monitor their networks for leakage to prevent ingress. Outside signals entering the cable can cause unwanted noise and picture ghosting. Excessive noise can overwhelm the signal, making it useless.

An ideal shield would be a perfect conductor with no holes, gaps or bumps connected to a perfect ground. However, a smooth solid copper shield would be heavy, inflexible, and expensive. Practical cables must make compromises between shield efficacy, flexibility and cost, such as the corrugated surface of hardline, flexible braid, or foil shields. Since the shields are not perfect conductors, electric fields can exist inside the shield, thus allowing radiating electromagnetic fields to go through the shield.

Consider the skin effect. The magnitude of an alternating current in a conductor decays exponentially with distance beneath the surface, with the depth of penetration being proportional to the square root of the resistivity. This means that in a shield of finite thickness, some small amount of current will still be flowing on the opposite surface of the conductor. With a perfect conductor (i.e., zero resistivity), all of the current would flow at the surface, with no penetration into and through the conductor. Real cables have a shield made of an imperfect, although usually very good, conductor, so there will always be some leakage.

The gaps or holes, allow some of the electromagnetic field to penetrate to the other side. For example, braided shields have many small gaps. The gaps are smaller when using a foil (solid metal) shield, but there is still a seam running the length of the cable. Foil becomes increasingly rigid with increasing thickness, so a thin foil layer is often surrounded by a layer of braided metal, which offers greater flexibility for a given cross-section.

This type of leakage can also occur at locations of poor contact between connectors at either end of the cable.

Ground loops

A continuous current flow, even if small, along the imperfect shield of a coaxial cable can cause visible or audible interference. In CATV systems distributing analog signals the potential difference between the coaxial network and the electrical grounding system of a house can cause a visible "hum bar" in the picture. This appears as a wide horizontal distortion bar in the picture that scrolls slowly upward. Such differences in potential can be reduced by proper bonding to a common ground at the house. See ground loop.

Induction

External current sources like switched-mode power supplies create a voltage across the inductance of the outer conductor between sender and receiver. The effect is less when there are several parallel cables, as this reduces the inductance and therefore the voltage. Because the outer conductor carries the reference potential for the signal on the inner conductor, the receiving circuit measures the wrong voltage.

Transformer effect

The transformer effect is sometimes used to mitigate the effect of currents induced in the shield. The inner and outer conductors form the primary and secondary winding of the transformer, and the effect is enhanced in some high quality cables that have an outer layer of mu-metal. Because of this 1:1 transformer, the aforementioned voltage across the outer conductor is transformed onto the inner conductor so that the two voltages can be cancelled by the receiver. Many sender and receivers have means to reduce the leakage even further. They increase the transformer effect by passing the whole cable through a ferrite core sometimes several times.

Common mode current and radiation

Common mode current occurs when stray currents in the shield flow in the same direction as the current in the center conductor, causing the coax to radiate.

Most of the shield effect in coax results from opposing currents in the center conductor and shield creating opposite magnetic fields that cancel, and thus do not radiate. The same effect helps ladder line. However, ladder line is extremely sensitive to surrounding metal objects which can enter the fields before they completely cancel. Coax does not have this problem since the field is enclosed in the shield. However, it is still possible for a field to form between the shield and other connected objects, such as the antenna the coax feeds. The current formed by the field between the antenna and the coax shield would flow in the same direction as the current in the center conductor, and thus not be canceled, and would actually cause energy to radiate from the coax itself, making it appear to be part of the antenna, affecting the radiation pattern of the antenna and possibly introducing dangerous radio frequency energy into areas near people, with the risk of radiation burns if the coax is being used for sufficiently high power transmissions. A properly placed and sized balun can prevent common mode radiation in coax.

Miscellaneous

Some senders and receivers use only a limited range of frequencies and block all others by means of an isolating transformer. Such a transformer breaks the shield for high frequencies. Still others avoid the transformer effect altogether by using two capacitors. If the capacitor for the outer conductor is implemented as one thin gap in the shield, no leakage at high frequencies occurs. At high frequencies, beyond the limits of coaxial cables, it becomes more efficient to use other types of transmission line such as wave guides or optical fiber, which offer low leakage (and much lower losses) around 200 THz and good isolation for all other frequencies.

Standards

This section includes a list of references or external links, but its sources remain unclear because it has insufficient inline citations. Please help to improve this article by introducing more precise citations where appropriate. (June 2009)

Most coaxial cables have a characteristic impedance of either 50, 52, 75, or 93 . The RF industry uses standard type-names for coaxial cables. Thanks to television, RG-6 is the most commonly-used coaxial cable for home use, and the majority of connections outside Europe are by F connectors.

A series of standard types of coaxial cable were specified for military uses, in the form "RG-#" or "RG-#/U". They date from WW II and were listed in MIL-HDBK-216 published in 1962. These designations are now obsolete. The RG designation stands for Radio Guide, the U designation stands for Universal. The current military standard is MIL-SPEC MIL-C-17. MIL-C-17 numbers, such as "M17/75-RG214," are given for military cables and manufacturer's catalog numbers for civilian applications. However, the RG-series designations were so common for generations that they are still used, although critical users should be aware that since the handbook is withdrawn there is no standard to guarantee the electrical and physical characteristics of a cable described as "RG-# type". The RG designators are mostly used to identify compatible connectors that fit the inner conductor, dielectric, and jacket dimensions of the old RG-series cables.

Table of RG standards

type

impedance

[ohms]

core

dielectric

overall diameter

braid

velocity factor

comments

type

[in]

[mm]

in

mm

RG-6/U

75

1.0 mm

Solid PE

0.185

4.7

0.270

6.86

double

0.75

Low loss at high frequency for cable television, satellite television and cable modems

RG-6/UQ

75

Solid PE

0.298

7.57

quad

This is "quad shield RG-6". It has four layers of shielding; regular RG-6 only has one or two

RG-8/U

50

2.17 mm

Solid PE

0.285

7.2

0.405

10.3

Amateur radio; Thicknet (10BASE5) is similar

RG-8/X

50

1.0 mm

Solid PE

0.185

4.7

0.270

6.86

double

0.75

A thinner version, with the electrical characteristics of RG-8U in a diameter similar to RG-6

RG-9/U

51

Solid PE

0.420

10.7

RG-11/U

75

1.63 mm

Solid PE

0.285

7.2

0.412

10.5

0.66

Used for long drops and underground conduit

RG-58/U

50

0.9 mm

Solid PE

0.116

2.9

0.195

5.0

single

0.66

Used for radiocommunication and amateur radio, thin Ethernet (10BASE2) and NIM electronics. Common.

RG-59/U

75

0.81 mm

Solid PE

0.146

3.7

0.242

6.1

single

0.66

Used to carry baseband video in closed-circuit television, previously used for cable television. Generally it has poor shielding but will carry an HQ HD signal or video over short distances.

RG-60/U

50

1.024 mm

Solid PE

0.425

10.8

single

Used for high-definition cable TV and high-speed cable Internet.

RG-62/U

92

Solid PE

0.242

6.1

single

0.84

Used for ARCNET and automotive radio antennas.

RG-62A

93

ASP

0.242

6.1

single

Used for NIM electronics

RG-174/U

50

0.48 mm

Solid PE

0.100

2.5

0.100

2.55

single

0.66

Common for wifi pigtails: more flexible but higher loss than RG58; used with LEMO 00 connectors in NIM electronics.

RG-178/U

50

70.1 mm

(Ag plated Cu clad Steel)

PTFE

0.033

0.84

0.071

1.8

single

0.69

RG-179/U

75

70.1 mm

(Ag plated Cu)

PTFE

0.063

1.6

0.098

2.5

single

0.67

VGA RGBHV

RG-213/U

50

70.0296 in Cu

Solid PE

0.285

7.2

0.405

10.3

single

0.66

For radiocommunication and amateur radio, EMC test antenna cables. Typically lower loss than RG58. Common.

RG-214/U

50

70.0296 in

PTFE

0.285

7.2

0.425

10.8

double

0.66

RG-218

50

0.195 in Cu

Solid PE

0.660 (0.680?)

16.76 (17.27?)

0.870

22

single

0.66

Large diameter, not very flexible, low loss (2.5dB/100' @ 400 MHz), 11kV dielectric withstand.

RG-223/U

50

0.88 mm

PE Foam

0.0815

2.07

0.212

5.4

Double

0.66

Sample RG-223 Datasheet

RG-316/U

50

7x0.0067 in

PTFE

0.060

1.5

0.098

2.6

single

0.695

used with LEMO 00 connectors in NIM electronics;

PE is Polyethylene; PTFE is Polytetrafluoroethylene; ASP is Air Space Polyethylene

Commercial designations

type

impedance

[ohms]

core

dielectric

overall diameter

braid

velocity factor

comments

type

[in]

[mm]

in

mm

H155

50

0.79

lower loss at high frequency for radiocommunication and amateur radio

H500

50

0.82

low loss at high frequency for radiocommunication and amateur radio

LMR-195

50

low loss drop-in replacement for RG-58

LMR-200

HDF-200

CFD-200

50

1.12 mm Cu

PF CF

0.116

2.95

0.195

4.95

0.83

low loss communications, 0.554 dB/meter @ 2.4 GHz

LMR-400

HDF-400

CFD-400

50

2.74 mm

(Cu clad Al)

PF CF

0.285

7.24

0.405

10.29

0.85

low loss communications, 0.223 dB/meter @ 2.4 GHz

LMR-600

50

4.47 mm

(Cu clad Al)

PF

0.455

11.56

0.590

14.99

0.87

low loss communications, 0.144 dB/meter @ 2.4 GHz

LMR-900

50

6.65 mm

(BC tube)

PF

0.680

17.27

0.870

22.10

0.87

low loss communications, 0.098 dB/meter @ 2.4 GHz

LMR-1200

50

8.86 mm

(BC tube)

PF

0.920

23.37

1.200

30.48

0.88

low loss communications, 0.075 dB/meter @ 2.4 GHz

LMR-1700

50

13.39 mm

(BC tube)

PF

1.350

34.29

1.670

42.42

0.89

low loss communications, 0.056 dB/meter @ 2.4 GHz

There are also other designation schemes for coaxial cables such as The URM, CT and WF series

References for this section

RF transmission lines and fittings. Military Standardization Handbook MIL-HDBK-216, U.S. Department of Defense, 4 January 1962.

Withdrawal Notice for MIL-HDBK-216 2001

Cables, radio frequency, flexible and rigid. Details Specification MIL-DTL-17H, 19 August 2005 (superseding MIL-C-17G, 9 March 1990).

Radio-frequency cables, International Standard IEC 60096.

Coaxial communication cables, International Standard IEC 61196.

Coaxial cables, British Standard BS EN 50117

H. P. Westman et al., (ed), Reference Data for Radio Engineers, Fifth Edition, 1968, Howard W. Sams and Co., no ISBN, Library of Congress Card No. 43-14665

http://www.rfcafe.com/references/electrical/coax-chart.htm

Talley Communications CAxT Cable Assembly

Specs for MIL-C-17 Coaxial Cable Q.P.L.

Times Microwave Systems LMR Wireless Products Catalog

CFD Cable Specifications

Specs of RG174/U, RG58C/U etc.

RG213/8, RG218, CLX1/4", CLX1/2", CLX7/8", CLX1+5/8" Cable Power & Impedance Specs

Velocity factor of various coaxial cables

Pasternack 2009 Catalog

Union Copper site with pictures, diagrams, and spec sheet

Uses

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Short coaxial cables are commonly used to connect home video equipment, in ham radio setups, and in measurement electronics. They used to be common for implementing computer networks, in particular Ethernet, but twisted pair cables have replaced them in most applications except in the growing consumer cable modem market for broadband Internet access.

Long distance coaxial cable is used to connect radio networks and television networks, though this has largely been superseded by other more high-tech methods (fibre optics, T1/E1, satellite). It still carries cable television signals to the majority of television receivers, and this purpose consumes the majority of coaxial cable production.

Micro coaxial cables are used in a range of consumer devices, military equipment, and also in ultra-sound scanning equipment.

The most common impedances that are widely used are 50 or 52 ohms, and 75 ohms, although other impedances are available for specific applications. The 50 / 52 ohm cables are widely used for industrial and commercial two-way radio frequency applications (including radio, and telecommunications), although 75 ohms is commonly used for broadcast television and radio.

Types

Hard line

1-5/8" hard line

Hard line is often confused with waveguide but the two are not the same. Hard line is used in broadcasting as well as many other forms of radio communication. It is a coaxial cable constructed using round copper, silver or gold tubing or a combination of such metals as a shield. Some lower quality hard line may use aluminum shielding, aluminum however is easily oxidized and unlike silver or gold oxide, aluminum oxide drastically loses effective conductivity. Therefore all connections must be air and water tight. The center conductor may consist of solid copper, or copper plated aluminum. Since skin effect is an issue with RF, copper plating provides sufficient surface for an effective conductor. Most varieties of hardline used for external chassis or when exposed to the elements have a PVC jacket; however, some internal applications may omit the insulation jacket. Hard line can be very thick, typically at least a half inch or 13 mm and up to several times that, and has low loss even at high power. These large scale hard lines are almost always used in the connection between a transmitter on the ground and the antenna or aerial on a tower. Hard line may also be known by trademarked names such as Heliax (Andrew), or Cablewave (RFS/Cablewave). Larger varieties of hardline may consist of a center conductor which is constructed from either rigid or corrugated copper tubing. The dielectric in hard line may consist of polyethylene foam, air or a pressurized gas such as nitrogen or desiccated air (dried air). In gas-charged lines, hard plastics such as nylon are used as spacers to separate the inner and outer conductors. The addition of these gases into the dielectric space reduces moisture contamination, provides a stable dielectric constant, as well as a reduced risk of internal arcing. Gas-filled hardlines are usually used on high powered RF transmitters such as television or radio broadcasting, military transmitters, as well as high powered amateur radio applications but may also be used on some critical lower powered applications such as those in the microwave bands. Although in the microwave region waveguide is more often used than hard line for transmitter to antenna, or antenna to receiver applications. The various shields used in hardline also differ; some forms use rigid tubing, or pipe, others may use a corrugated tubing which makes bending easier, as well as reduces kinking when the cable is bent to conform. Smaller varieties of hard line may be used internally in some high frequency applications, particularly in equipment within the microwave range, to reduce interference between stages of the device.

Radiating

Main article: Leaky feeder

Radiating or Leaky Cable is another form of coaxial cable which is constructed in a similar fashion to hard line, however it is constructed with tuned slots cut into the shield. These slots are tuned to the specific RF wavelength of operation or tuned to a specific radio frequency band. This type of cable is to provide a tuned bi-directional "desired" leakage effect between transmitter and receiver. It is often used in elevator shafts, underground, transportation tunnels and in other areas where an antenna is not feasible. One example of this type of cable is Radiax (Andrew).

RG/6

Main article: RG/6

RG/6 is available in three different types designed for various applications. "Plain" or "house" wire is designed for indoor or external house wiring. "Flooded" cable is infused with heavy waterproofing for use in underground conduit (ideally) or direct burial. "Messenger" may contain some waterproofing but is distinguished by the addition of a steel messenger wire along its length to carry the tension involved in an aerial drop from a utility pole.

Triaxial cable

Main article: Triaxial cable

Triaxial cable or triax is coaxial cable with a third layer of shielding, insulation and sheathing. The outer shield, which is earthed (grounded), protects the inner shield from electromagnetic interference from outside sources.

Twin-axial cable

Main article: Twinaxial cabling

Twin-axial cable or twinax is a balanced, twisted pair within a cylindrical shield. It allows a nearly perfect differential signal which is both shielded and balanced to pass through. Multi-conductor coaxial cable is also sometimes used.

Biaxial cable

Main article: Twin-lead

Biaxial cable, biax or Twin-Lead is a figure-8 configuration of two 50 coaxial cables, externally resembling that of lamp cord, or speaker wire. Biax is used in some proprietary computer networks. Others may be familiar with 75 biax which at one time was popular on many cable TV services.

Semi-rigid

Semi-rigid cable is a coaxial form using a solid copper outer sheath. This type of coax offers superior screening compared to cables with a braided outer conductor, especially at higher frequencies. The major disadvantage is that the cable, as its name implies, is not very flexible, and is not intended to be flexed after initial forming. (See "hard line")

Conformable cable is a flexible reformable alternative to semi-rigid coaxial cable used where flexibility is required. Conformable cable can be stripped and formed by hand withouth the need for specialist tools, similar to standard coaxial cable.

Interference and troubleshooting

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2009)

Coaxial cable insulation may degrade, requiring replacement of the cable, especially if it has been exposed to the elements on a continuous basis. The shield is normally grounded, and if even a single thread of the braid or filament of foil touches the center conductor, the signal will be shorted causing significant or total signal loss. This most often occurs at improperly installed end connectors and splices. Also, the connector or splice must be properly attached to the shield, as this provides the path to ground for the interfering signal.

Despite being shielded, interference can occur on coaxial cable lines. Susceptibility to interference has little relationship to broad cable type designations (e.g. RG-59, RG-6) but is strongly related to the composition and configuration of the cable's shielding. For cable television, with frequencies extending well into the UHF range, a foil shield is normally provided, and will provide total coverage as well as high effectiveness against high-frequency interference. Foil shielding is ordinarily accompanied by a tinned copper or aluminum braid shield, with anywhere from 60 to 95% coverage. The braid is important to shield effectiveness because (1) it is more effective than foil at absorbing low-frequency interference, (2) it provides higher conductivity to ground than foil, and (3) it makes attaching a connector easier and more reliable. "Quad-shield" cable, using two low-coverage aluminum braid shields and two layers of foil, is often used in situations involving troublesome interference, but is less effective than a single layer of foil and single high-coverage copper braid shield such as is found on broadcast-quality precision video cable.

In the United States and some other countries, cable television distribution systems use extensive networks of outdoor coaxial cable, often with in-line distribution amplifiers. Leakage of signals into and out of cable TV systems can cause interference to cable subscribers and to over-the-air radio services using the same frequencies as those of the cable system.

History

1866 First successful transatlantic cable, designed by William Thomson (Lord Kelvin, 1892); see Submarine communications cable.

1880 Coaxial cable patented in England by Oliver Heaviside, patent no. 1,407.

1884 Siemens & Halske patent coaxial cable in Germany (Patent No. 28,978, 27 March 1884).

1894 Oliver Lodge demonstrates waveguide transmission at the Royal Institution. Nikola Tesla receives U.S. Patent 0,514,167, Electrical Conductor, on February 6.

1929 First modern coaxial cable patented by Lloyd Espenschied and Herman Affel of AT&T's Bell Telephone Laboratories, U.S. Patent 1,835,031.

1936 First transmission of TV pictures on coaxial cable, from the 1936 Summer Olympics in Berlin to Leipzig.

1936 World's first underwater coaxial cable installed between Apollo Bay, near Melbourne, Australia, and Stanley, Tasmania. The 300 km cable can carry one broadcast channel and seven telephone channels.

1936 AT&T installs experimental coaxial telephone and television cable between New York and Philadelphia, with automatic booster stations every ten miles. Completed in December, it can transmit 240 telephone calls simultaneously.

1936 Coaxial cable laid by the General Post Office (now BT) between London and Birmingham, providing 40 telephone channels.

1941 First commercial use in USA by AT&T, between Minneapolis, Minnesota and Stevens Point, Wisconsin. L1 system with capacity of one TV channel or 480 telephone circuits.

1956 First transatlantic coaxial cable laid, TAT-1.

See also

Radio frequency power transmission

L-carrier

Balanced pair

Data cable

Shielded cable

Cable

Category 5 cable

References

^ Nahin, Paul J. (2002). Oliver Heaviside: The Life, Work, and Times of an Electrical Genius of the Victorian Age. ISBN 0801869099. 

^ http://www.smarthome.com/7807R/Right-Angle-F-Connector-Adapters-6-Pack-2125/p.aspx

^ Elmore, William C.; Heald, Mark A. (1969). Physics of Waves. ISBN 0486649261. 

^ Ott, Henry W. (1976). Noise Reduction Techniques in Electronic Systems. ISBN 0471657263. 

^ RF Cafe - Coaxial Cable Specifications Cables Chart

^ "Radio City Inc". http://www.radioinc.com/oscmax/catalog/product_info.php?name=LMR 400 UltraFlex (RG-8) 100 ft pre-cut&products_id=1121. 

^ "Andrew Heliax". http://www.commscope.com/andrew/eng/product/trans_line_sys/coaxial/wireless/1206774_13612.html. 

^ "Cablewave Radio Frequency Systems (http://www.rfsworld.com)". http://www.rfsworld.com/. 

^ "Andrew Radiax". http://www.commscope.com/andrew/eng/product/trans_line_sys/coaxial/radiating/1206639_13611.html. 

^ IEEE - IEEE History Center: Landing of the Transatlantic Cable, 1866

^ Atlantic-cable.com - History of the Atlantic Cable & Undersea Communications from the first submarine cable of 1850 to the worldwide fiber optic network

^ HistoryMagazine.com - The Transatlantic Cable

^ PBS.org - The First Attempts to Lay the Transatlantic Cable (1857-1858)

^ Britannica.com - transatlantic cable

^ Google Book Search - Oliver Heaviside By Paul J. Nahin

^ Feldenkirchen, Wilfried (1994). Werner von Siemens - Inventor and International Entrepreneur. ISBN 0814206581. 

^ "Coaxial Debut," Time, Dec. 14, 1936.

^ Boing Boing - Gallery: An illustrated history of the transoceanic cable

^ Google books - Broadcast engineer's reference book By Edwin Paul J. Tozer

^ Radio-electronics.com - Coaxial feeder or RF coax cable

^ Atlantic-cable.com - 1956 TAT-1 Silver Commemorative Dish

^ Google books - The worldwide history of telecommunications By Anton A. Huurdeman

Wikimedia Commons has media related to: Coaxial cables

v  d  e

RF connectors (coaxial)

APC-7  BNC  C  F  FME  Hirose U.FL  IPX  Motorola  MCX  MMCX  N  QLS  QMA/QN  RCA  SMA  SMB  SMC  Twin-lead  TNC  TV aerial plug  UHF / Mini-UHF

Variations and alternate names: 2.9 mm (SMA)  7 mm  Triax / Triaxial  Twin BNC / Twinax (BNC)  IPEX   MHF   AMC (UFL)  SnapN  RP-TNC  RP-SMA

Old or seldom used: EIA  GR  LEMO 00  Musa

See also: Radio frequency  Radio spectrum  Audio and video connectors  Audio and video interfaces and connectors

Categories: Signal cables | Antennas (radio)Hidden categories: Articles needing additional references from June 2009 | All articles needing additional references | All articles with unsourced statements | Articles with unsourced statements from June 2007 | Articles lacking in-text citations from June 2009 | All articles lacking in-text citations
About the Author

I am a professional writer from China Hardware Suppliers, which contains a great deal of information about $keyword_li, welcome to visit!

Motorola / SB5101 SURFBOARD CABLE MODEM / 567005-005-00 $76.16 Motorola - SB5101 SURFBOARD CABLE MODEM - 567005-005-00

Motorola SURFboard SB5101 USB Cable Modem 56700500500 $67.37 Motorola SURFboard SB5101 USB Cable Modem 56700500500

Motorola DSL/Ethernet Cable Modem 2210-02-1006 $64.5 Motorola DSL/Ethernet Cable Modem 2210-02-1006

Motorola Null Modem Cable $19.99 1 x 9-pin DB-9 Female RS-232 Serial 25-96992-01R Copper DB-9 Data Transfer Cable Motorola Motorola, Inc Null Modem Cable www.motorola.com/us

Motorola SURFboard Cable Modem $59.99 Get more out of your time online. Surf the Web and view pages quickly, download video with blazing speed and play online games faster than your opponents with this SURFboard cable modem.

Motorola SURFboard SBG901 Wireless Cable Modem Gateway 55631500500 $102.34 Motorola SURFboard SBG901 Wireless Cable Modem Gateway 55631500500

Motorola SURFboard SBG901 Wireless Cable Modem Gateway - Wireless Router - Cable Modem - 802.11b/g - Desktop. Each $103.64 Manufacturer: Motorola. Each. Motorola's SBG901 SURFboard Wireless Cable Modem Gateway combines an industry-leading cable modem, an IEEE 802.11b/g wireless access point, and an advanced firewall into one compact product. It's the perfect networking soluti

Motorola SURFboard SB5101 USB Cable Modem $60.99 1 x F-type Network WAN 1 x RJ-45 10/100Base-TX Network LAN 1 x USB LAN 128QAM 256QAM 30 Mbps Upstream 38 Mbps 38 Mbps Downstream 567005-005-00 6.20" Height x 2.30" Width x 6" Depth Motorola's SURFboard SB5101 Cable Modem incorporates the latest DOCSIS 2.0 Advanced Time Division Multiple Access (A-TDMA) and Synchronous Code Division Multiple Access (S-CDMA) technologies to provide up to three times greater upstream capacity than DOCSIS 1.0/1.1 systems. Packed with power, the SB5101 is interoperable and backward compatible with DOCSIS 1.0 and 1.1 for a fast and timely transition operators can deploy the SB5101 today without a service interruption. Cable Modem Ethernet External Motorola Motorola, Inc RJ-45 Retail SB5101 SURFboard SURFboard SB5101 USB Cable Modem USB www.motorola.com/us

MOTOROLA SBG901 SURFboard Wireless Cable Modem Gateway $85.99 Interface: Ethernet Port Cable Interface: 1 x F-type Network WAN Standards: DOCSIS 2.0/1.1 Features: Motorola's SBG901 SURFboard Wireless Cable Modem Gateway is the perfect networking solution for the home, home office, or small business. It combines an industry leading DOCSIS 2.0 cable modem, an advanced firewall, and an 802.11b/g wireless access point all in a stylish enclosure for the sophisticated consumer. The SBG901 allows users to create a custom LAN to share a single broadband connection, files, printers, and peripherals without wires. Parts: 2 years limited Labor: 2 years limited

MOTOROLA SB5101U SURFboard Cable Modem $54.99 Interface: USB and Ethernet 10/100Base-T Cable Interface: F-Connector, female, 75ohm Standards: DOCSIS 2.0 Features: Integrated A-TDMA and S-CDMA technology — capable of providing up to 30 Mbps upstream data rate WHQL certified USB drivers for Windows 2000/Me/XP New stylish case saves valuable desk space Front panel status LEDs and built-in HTML-based diagnostics for quick and easy troubleshooting USB and Ethernet connectivity simplifies installation Compatible with Windows 95/98/2000/Me/NT/XP, Mac, Linux and UNIX Supports up to 63 computers on a single Internet connection (additional networking hardware required) Capable of downloading at speeds up to 500 times faster than 56.6k analogue phone modem No telephones lines needed — always on, always connected Parts: 2 years limited Labor: 2 years limited...

Motorola SURFboard 6120 DOCSIS Cable Modem $88.99 1 Gbps Gigabit Ethernet 1 x F-type 1 x RJ-45 10/100/1000Base-T LAN 10 Mbps Ethernet 100 Mbps Fast Ethernet 128QAM 131.07 Mbps Maximum Upstream @ 128QPSK 16QAM 222.46 Mbps 222.46 Mbps Maximum Downstream @ 256QAM 256QAM 32QAM 5.70" Height x 5.70" Width x 1.50" Depth 545101-011-00 6120 64QAM 8QAM DOCSIS EURO DOCSIS 3.0 Supports IP addressing using IPv4 and/or IPv6 (dual stack) Security: DOCSIS 3.0 Security (3PI+, EAE, SSD) Network Management: SNMP v2, v3 The Motorola SURFboard Cable Modem SB6120 is DOCSIS and Euro-DOCSIS 3.0 certified. It introduces channel bonding of up to 4 downstream channels and 4 upstream channels allowing operators to offer their customers advanced multimedia services with data rates of well over 100 Mbps in each direction without upgrading their HFC plant. The SB6120 supports all DOCSIS 3.0 features including channel bonding, IPv6, and Advanced Encryption Services. Cable Modem Ethernet External Motorola Motorola, Inc QPSK RJ-45 SURFboard SURFboard 6120 DOCSIS Cable Modem www.motorola.com/us

Motorola Modem Surfr External Modem 3645 $88.29 Motorola Modem Surfr External Modem 3645

modem cable $19.99 Atek - Modem cable (M) - RJ-11 (F)

Motorola 56700500500 Surfboard Cable Modem Docsis 2 $96.53 Motorola s SURFboard SB5101 Cable Modem incorporates the latest DOCSIS 2.0 Advanced Time Division Multiple Access (ATDMA) and Synchronous Code Division Multiple Access (SCDMA) technologies to provide up to three times greater upstream capacity than DOCSIS 1.0/1.1 systems. Packed with power the SB5101 is interoperable and backward compatible with DOCSIS 1.0 and 1.1 for a fast and timely transition operators can deploy the SB5101 today without a service interruption. Data Transfer Rate: 38 Mbps Downstream and 30 Mbps Upstream. Dimensions: 6.20 H x 2.30 W x 6 D. Maximum Transmission Speed: 38 Mbps. 1 x Type F Connector 1 x RJ45 10/100BaseTX 1 x USB Interfaces/Ports.

MOTOROLA SB6121 SURFboard Cable Modem $87.99 Interface: RJ-45 Cable Interface: 75ohm F-connector Features: Data Protocol: TCP/IP Power: 9W (nominal) Input Power: 105 to 125 VAC, 60 Hz Downstream: -Modulation: 64 or 256 QAM -Capture Bandwidth: 100 MHz (edge to edge) -Maximum Theoretical Data Rate: DOCSIS: 171.537 Mbps (4 channels) / 42.884 (single channel)@ 256 QAM at 5.36 Msym/s EuroDOCSIS: 222.464 Mbps (4 channels) / 55.616 (single channel)@ 256 QAM at 6.952 Msym/s. -Bandwidth: DOCSIS: = 24 MHz EuroDOCSIS: = 32 MHz. -Symbol Rate: DOCSIS: 64 QAM 5.057 Msym/s; 256 QAM 5.361 Msym/s EuroDOCSIS: 64 QAM 6.952 Msym/s; 256 QAM 6.952 Msym/s. -Operating Level Range: –15 to 15 dBmV -Security: DOCSIS 3.0 Security (BPI+, EAE, SSD) -Network Management: SNMP v2 & v3 -Provisioning Supports: IP addressing using IPv4 and/or IPv6 (dual stack). Upstream: -Modulation:...

SB5101 SURFBOARD CABLE MODEM $59.99 SB5101 SURFBOARD CABLE MODEM

Zoom 5341 Cable Modem $170.47 Cable Modem DOCSIS 3.0

Modem $114.71 Modem. Modulation, Demodulation, Frequency shift keying, Cable modem, DSL modem, Serial communication, Radio modem, Wavelength division multiplexing, Phase shift keying, Duplex (telecommunications), Hayes Microcomputer Products, Hayes command set, Bulletin board system, Softmodem, SupraFAXModem 14400, Wireless modem, General Packet Radio Service, Universal Mobile Telecommunications System, Evolution Data Optimized, WiMAX, Orthogonal frequency division multiplexing Author: Miller, Frederic P./ Vandome, Agnes F./ McBrewster, John Binding Type: Paperback Number of Pages: 152 Publication Date: 2009/10/08 Language: English Dimensions: 5.98 x 9.01 x 0.35 inches

Motorola DDS/MR56 External Modem 6456522600010 $41.5 Motorola DDS/MR56 External Modem 6456522600010

Motorola Modem Rack Mount V3400 $94.75 Motorola Modem Rack Mount V3400

Motorola Rack Mount Modem V3225 $65.25 Motorola Rack Mount Modem V3225

Motorola 2240 Modem Card 2240 $66.25 Motorola 2240 Modem Card 2240

Motorola / Motorola Modem Module Dongle Kit / KT-70924-02R $242.91 Motorola - Motorola Modem Module Dongle Kit - KT-70924-02R

Motorola SURFboard DOCSIS 30 High-Speed Cable Modem $99.99 This cable modem features Gigabit Ethernet connectivity for fast downstream and upstream data speeds. Six multicolor LEDs indicate the operational status and a color-coded rear panel ensures simple installation.

Motorola SURFboard SB6121 Cable Modem - 1 x F-type , 1 x RJ-45 10/100/1000Base-T Network LAN - 222.46 Mbps - External 575319... $97.5 Motorola SURFboard SB6121 Cable Modem - 1 x F-type , 1 x RJ-45 10/100/1000Base-T Network LAN - 222.46 Mbps - External 575319...

5341J DOCSIS 3.0 Cable Modem - cable modem $95.99 Zoom 5341J DOCSIS 3.0 Cable Modem - Cable modem - external - Gigabit Ethernet - 343 Mbps

5341 DOCSIS 3.0 Cable Modem - cable modem $85.99 Zoom 5341 DOCSIS 3.0 Cable Modem - Cable modem - external - Gigabit Ethernet - 172 Mbps

RS232 null modem cable $18.95 RS232 SERIAL/NUL MODEM CABLE FOR DREAMBOX

Belkin / Belkin Modem Cable / F2L088-06 $17.08 Belkin - Belkin Modem Cable - F2L088-06

Belkin / Belkin Modem Cable / F3L641-14 $16.62 Belkin - Belkin Modem Cable - F3L641-14

HP Modem Cable Kit PF2101ACK002 $37.33 HP Modem Cable Kit PF2101ACK002

Atek Modem Cable $16.99 1 1 x 15-pin Male PCMCIA 1 x RJ-11 Female 72" Actiontec and generics Modem BFM5603-LF, EF144, EF288, EF336, FM288B, GFM5600-RF, MD28800, ML33602, ML28800,Apache Micro Modem 33.6 - V34PCM-R, 56K - A56PCM-RBest Data Modem 56PC + 56SPCBoca research Modem MV.34PC/MD56PCCardinal Modem MVP144C2, MVP288C2, MVP336C2, MVPV24PC, MVPV34PCompaq Modem 61-001Diamond Multimedia Modem Supra Modem PC Card 56KThinfax Modem 28.8 - 33.6Eigercom Modem 28.8 33.6 56KHayes Modem Accura Modem 5684US, 5361US,Optima Modem 533PAM, 288 T2 535PAM, 336 T2 5346New Media Modem Novalink Modem Performance Modem 28.8Piiceon Modem 14.4 28.8, 8043400, 8043400ECPractical Peripherals Modem 5688USSilicom Modem Modem Master Modem 56KSimple Technology Modem 14.4, 28.8, 33.6, 56K 15-pin typeViking Modem all 15-pin typesZoom Technologies Modem 28.8 - 33.6, 56K Dual mode (not cards with Lucent chipset, I.E. Not cards with L, towards the End of Card Part #) Durable molded telephone plug Atek Atek, Inc Copper Modem Modem Cable Network Cable PCCA-M-15-1 RJ-11 Replacement cable for many brands and models of 15-pin PC card (PCMCIA) modems. Retail www.atek.com

MOTOROLA SBG6580 SURFboard Wireless Cable Modem Gateway $130.99 Interface: Ethernet Port Standards: DOCSIS/EuroDOCSIS 3.0 Features: Integrated 802.11n wireless access point, 2 x 2 antenna array Switched, onboard radios: 2.4 or 5 GHz Four Gigabit Ethernet ports enable flexible, high-speed connectivity with Auto Negotiate and Auto MDIX Compatible with Windows, Macintosh and Unix computers Extensible networking, allowing customer to network up to 253 desktop computers, laptops and other Ethernet or wireless devices to create a full Class C network Support for multicast IP services Wi-Fi Security WEP/WPA/WPA2 Advanced firewall with DoS protection and intrusion prevention Wi-Fi Wizard for secure PC client setup Remote configuration and monitoring from the headend using SNMP and TFTP Enhanced security: supports AES traffic encryption Plug-and-play installation Wi-Fi Pairing button for easy Wi-Fi Pr...

Motorola V3229 14.4Kbps External Analog Modem 6209526200030 $66.25 Motorola V3229 14.4Kbps External Analog Modem 6209526200030

Motorola 3260 Fast Data Modem With V.34 21800 $176.45 Motorola 3260 Fast Data Modem With V.34 21800

Motorola Rack Mount Modem Card 212A $95.25 Motorola Rack Mount Modem Card 212A

Motorola UDS 103 LP External Modem 103LP $95.25 Motorola UDS 103 LP External Modem 103LP

Motorola 9600A Full Size Modem External 62095030 $298.25 Motorola 9600A Full Size Modem External 62095030

modem cable - 10 ft $8.99 C2G - Modem cable - DB-25 (M) - DB-25 (M) - 10 ft

This entry was posted on Saturday, December 26th, 2009 at 8:22 pm and is filed under Uncategorized. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.